塑封機日常保養注意事項

1、環境對塑封的影響：塑封機預熱穩定時間受環境溫度的影響, 環境溫度高時, 塑封溫度能較快平衡穩定環境溫度低時, 散熱快,塑封溫度需較長時間才能達到平衡穩定。切忌開機后溫度顯示剛到塑封溫度就進行塑封, 因為此時塑封機膠輥受熟尚未平衡穩定, 只是測溫點附近局部溫度達到塑封溫度。一般來講預熱穩定時間不要短于20分鐘。塑封機工作環境設計指標為一5~40℃ ,相對濕度不大于80%, 無腐蝕性氣體。因此, 一般季節及氣候條件下塑封機均能正常工作, 不會影響塑封效果。

2、膠輥硬度對塑封的影響塑封機膠輥硬度為肖氏50度。若膠輥因老化等原因引起變硬或開裂時, 將影響塑封質量, 會使過塑的證件塑封不牢, 需及時更換膠輥。

3、塑封質量檢查經塑封后的證件應透明、平整、塑封套與卡芯應牢固封合為一體。夾層內無' 氣飽' , 無' 模糊白色印影' , 無油污、雜質等不良現象。常見的幾種異常現象和判斷發生的原因, 如局部未封牢, 應考慮塑封溫度偏低如出現塑封后證件變形起皺折, 應考慮為塑封溫度過高或壓力太大如出現夾層內有氣泡或模糊白色印影, 應考慮為塑封溫度不合適如出現塑封過程中粘合劑外溢, 則應考慮為塑封溫度過高或壓力太大。