隔墻龍骨間距規范要求

1、隔墻龍骨的間距規范如果按國家建筑室內裝修執行標準的話是，是在三十公分到四十公分左右。

2、輕鋼龍骨隔墻的高度要在六米以內，而且上面必須要到頂，這樣連成了整度才會牢固。

3、輕鋼龍骨隔墻在施工的時候，室內主體結構要是已經驗收的，環境溫度要在5度以上。施工人員要先熟悉圖紙，然后根據要求進行彈線定位。

4、然后依次安裝固定沿項、沿地龍骨、邊框龍骨、支撐卡系列龍骨、豎向龍骨、通貫系龍骨。龍骨邊線要與彈線重合，固定沿項、沿地龍骨固定點間距要在600MM以內，邊框龍骨固定點間距要在1米以內。

5、龍骨安裝好以后，要檢查一下隔斷骨架的牢固程度，龍骨的立面垂直偏差要在3MM以內，表面不平整要在2MM以內。再安裝石膏罩面板，然后進行接縫與護角的處理，如果隔斷板下面有木踢腳線，罩面板要距地面20—30MM左右。

隔墻龍骨安裝方法

1、安裝隔斷墻之前，首先需要確定墻位，需要在地面上放出線，要將線直到天花板上。接下來對地面墻面進行清洗，再涂上一層處理劑，準備好其他的材料。

2、然后要將龍骨準備到位，用射釘進行固定，要確定豎向和橫向的龍骨間距，沿著龍骨分檔劃線。

3、接下來先固定天地的龍骨，再安裝豎龍骨，最后穿骨。要用木工條進行固定，固定好了之后，還要用石膏板來安裝，最好用自攻螺絲進行固定。

4、然后就要固定門窗框，可以用木螺絲進行固定，最后安裝石膏板，將接縫處用泡沫膠做好密封工作，再在墻面上做一下裝飾，完成整個安裝的流程。

隔墻龍骨配件有哪些

1、隔墻龍骨一般有C型龍骨與U型龍骨，其中C型龍骨的寬度有100mm、75mm、50mm，翼寬50mm，長度3000mm，用于非承重隔墻系統中的豎向龍骨框架。

2、U型龍骨的寬度有100mm、75mm、50mm，翼寬40mm，長度3000mm，用于非承重隔墻系統的周邊龍骨。吊頂龍骨與隔墻龍骨是不一樣的。

3、龍骨材料主要有沿頂沿地龍骨、加強龍骨、豎橫向龍骨與橫撐龍骨，配件有支撐卡、卡托、角托、連接件、固定件、護角條、壓縫條等。